Results 1 - 10 for Pound-force per square inch

Questions to Ask
A B C D E F G H I J K L M N O P Q R S T U V W 153 Dixon Sanitary 2009 Catalog 1-800-789-1718 1 Pound Force Per Square Inch = 144 Pound Force Per Square Foot = 0.068 Atmosphere = 2 ...
http://www.bradfordfittings.com/dpl/dpl_page/2009/153.pdf
open  pop

Recommended Unit Symbols, SI Prefixes, and Abbreviations
weber Wb second (time) s yard yd 2 2 2 2 2 2 2 2 § Although the use of the abbreviation psi is common, it is not recommended. See pound-force per square inch.
http://www.ewh.ieee.org/soc/ias/pub-dept/abbreviation.pdf
open  pop

MIL-H-28693 Hose, Rubber, Oil and Gasoline Discharge, Smooth Bore ...
The hose shall withstand a proof pressure of 300 pound-force per square inch gage (psig) without leakage or other indication of weakness when tested according to 4.5.3.
http://www.wbdg.org/ccb/FEDMIL/h28693.pdf
open  pop

METRIC CONVERSION TABLE
... 03 pound-force per square inch (psi) (lbf/in 2) kilopascal (kPa) 6.894 757 E+00 psi (pound-force per square inch) (lbf/in 2) pascal (Pa) 6.894 757 E+03 psi (pound-force per square inch ...
http://wtc.nist.gov/progress_report_june04/metric_conversion.pdf
open  pop

F-V-2906 Valves, Air Venting, Steam
class I-Low pressure-up to 15 pound-force per square inch gage (psig) F-V-2906 Valves, Air Venting, Steam
http://www.wbdg.org/ccb/FEDMIL/fv2906.pdf
open  pop

Symbols and Prefixes
... pound-force lbf megavar Mvar pound-force foot lbfft megawatt MW pound-force per square inch lbf/in megohm Mþ pound (force) per square inch lbf/in metal-oxide semiconductor MOS power factor PF meter ...
http://www.ieee.org/portal/cms_docs_pes/pes/subpages/authors-folder/authkit-folder/authkitjan2001/PG9-sympref.pdf
open  pop

VISUALIZING SI UNITS
... per square centimeter pieze pound-force per square inch (psi) 4.018 60 1.866 48 inch of water (60 ° F) millimeter of mercury (0 ° C) inH 2 O mmHg pound-force per square foot centimeter of ...
http://www.wildi-theo.com/fichiers/documents/contenu/charts/pressure_and_stress.pdf
open  pop

CIP 35 - Testing Compressive Strength of Concrete
The compressive strength is calculated from the failure load divided by the cross-sectional area resisting the load and reported in units of pound-force per square inch (psi) in US ...
http://nrmca.org/aboutconcrete/cips/35p.pdf
open  pop

29 metric SI units:  7 base units: metre, kilogram, second ...
... pound (basis weight of newsprint), poundal, poundals per square foot, pound-force, pound-force foot, pound-force inch, pound-force per square foot, pound-force per square inch ...
http://www.metricationmatters.com/docs/SIMetricUnitsVsUSAMeasures.pdf
open  pop

Explosion Pressure Design Criteria for New Seals in U.S. Coal Mines
... ms millisecond m/s meter per second pcf pound per cubic foot psi pound-force per square inch psia pound-force per square inch absolute psig pound-force per square inch ...
http://www.cdc.gov/niosh/mining/pubs/pdfs/2007-144.pdf
open  pop

Featured Results: